Skyworker的筆記: WAP-7531 MESH的開機程序

Boot reached stage 13

Boot reached stage 12

Valid CRC found in flash restoring env...

Boot reached stage 11

board_hw_config_iterate: bc_phy1_addr value from config 3 doesn't match expected value 1

hw_config_id 65535: 'QHS860'

Cold boot

Reset status: 0x00000001

PCIe early init, done@461ms

Info: data uncached: addr=0xc0000000 size=1024MB

Info: text at 0x98040000, stack at 0x98013ffc(8192), heap at 0x98000000(73728), uboot size 182700

Info: i-cache is enabled

Info: d-cache is enabled

Info: CPU freq is 500000000, dev freq is 125000000

Info: Quantenna U-Boot version:SEv1.2v37.4.0.198

Info: build date ' 5月 30 2019', time '14:50:24'

SPI flash info:

name : mx25l25635f

jedec_id : 0xc22019

sector size : 65536

number of sector : 512

frequency : 104000000

flags : 0x0

lock :

DDR_INIT: type = 16, speed = 2, size = 268435456, rev = 0x43, param = 0x0

DDR_INIT: replacing invalid param = 0x0 with default 0xe7b

500MHz

init board as PCIe Root Complex mode

BDA at 0x80002000

In: serial

Out: serial

Err: serial

Boot reached stage 64

PHY found on MDIO addr:1

PHY 0x1cc915 found on MDIO addr:1

Enable phy SSC

PHY found on MDIO addr:3

PHY 0x1cc915 found on MDIO addr:3

Enable phy SSC

Boot reached stage 65

Hit any key to stop autoboot: 0

get_qtnboot_envvars: vars: safety_image_addr 0x40000 safety_image_size 0x9e0000 live_image_addr 0xa20000 live_image_size 0x9e0000

do_bootselect: spi_flash read 0x00040000 0x83000000 0x009e0000

Read: flash=0x40000 mem=0x83000000 size=10354688 ret_size=10354688

do_bootselect: bootm 0x83000000

Boot reached stage 1

## Booting kernel from Legacy Image at 83000000 ...

Boot reached stage 2

Boot reached stage 3

Image Name: SE3.0.0.3

Image Type: arc Linux Kernel Image (lzma compressed)

Data Size: 8712835 Bytes = 8.3 MB

Load Address: 8493a000

Entry Point: 8493a000

Qtn flags: 00000001

Signature value:

55 bc 71 8c d5 e4 e6 6c 83 69 cd 47 17 4c ef 15

Verifying Checksum ... OK

Boot reached stage 4

Boot reached stage 5

rsa,num-bits: 2048

rsa,n0-inverse: 0x193908d9

Certification check successfully

Boot reached stage 6

Boot reached stage 14

Uncompressing Kernel Image ... OK

Boot reached stage 7

Boot reached stage 8

Command line TAG setup

Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 mtdparts=spi_flash:128k(uboot),64k(uboot_env),64k(uboot_env_bak),10112k(linux_safety),10112k(linux_live),-(data)

p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 mtdparts=spi_flash:128k(uboot),64k(uboot_env),64k(uboot_env_bak),10112k(linux_safety),10112k(linux_live),-(data)

## Unset TAG qtn_flags 1

## Transferring control to Linux (at address 8493a000) ATAG parameters 9806a0b4 - 9806a17c...

[ 0.000000] Linux version 2.6.35.12 (wilson@volume.local) (gcc version 4.2.3 (ARC_2.3)) #268 Tue Jun 9 16:39:05 CST 2020

[ 0.000000] Parsing ATAG parameters from bootloader

[ 0.000000] ATAG_CORE: successful parsing

[ 0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 mtdparts=spi_flash:128k(uboot),64k(uboot_env),64k(uboot_env_bak),10112k(linux_safety),10112k(linux_live),-(data)

[ 0.000000] Board id: 65535

[ 0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535

[ 0.000000]

[ 0.000000] Processor Family: ARC 700 [0x33]

[ 0.000000] CPU speed : 500.00 Mhz

[ 0.000000] Timers: TIMER1 TIMER0

[ 0.000000] Interrupt Vect Base: 0x98051c00

[ 0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000

[ 0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB

[ 0.000000] ARC700 MMU Ver [2]

[ 0.000000] PAGE SIZE 8k

[ 0.000000] JTLB 128 x 2 = 256 entries

[ 0.000000] uDTLB 8 entr, uITLB 4 entr

[ 0.000000] TLB Refill "will NOT" Flush uTLBs

[ 0.000000] Detected I-cache :

[ 0.000000] Type=2 way set-assoc, Line length=32, Size=16K (enabled)

[ 0.000000] Detected D-cache :

[ 0.000000] Type=4 way set-assoc, Line length=32, Size=16K (enabled)

[ 0.000000] Extensions:

[ 0.000000] MPY: 32x32 with ANY Result Reg MAC MPY: Dual 16 x 16 and 32 x 16

[ 0.000000] DCCM: N/A ICCM: N/A

[ 0.000000] CRC: N/A, SWAP: Present NORM: Present

[ 0.000000] Min-Max: Present, Barrel Shifter: Present

[ 0.000000] Ext Arith Insn: Present

[ 0.000000] Floating Point Extension: N/A

[ 0.000000] On node 0 totalpages: 32767

[ 0.000000] free_area_init_node: node 0, pgdat 865c82dc, node_mem_map 8667a024

[ 0.000000] Normal zone: 144 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 32623 pages, LIFO batch:7

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32623

[ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 mtdparts=spi_flash:128k(uboot),64k(uboot_env),64k(uboot_env_bak),10112k(linux_safety),10112k(linux_live),-(data)

[ 0.000000] bootconsole [ruby_early0] enabled

[ 0.000000] PID hash table entries: 1024 (order: -1, 4096 bytes)

[ 0.000000] Dentry cache hash table entries: 32768 (order: 4, 131072 bytes)

[ 0.000000] Inode-cache hash table entries: 16384 (order: 3, 65536 bytes)

[ 0.000000] Memory: 155776KB available (2220K code,1235K data, 26488K init)

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] RCU debugfs-based tracing is enabled.

[ 0.000000] Verbose stalled-CPUs detection is disabled.

[ 0.000000] clockevent mode switch to [1]

[ 0.000000] clockevent mode switch to [2]

[ 0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592)

[ 0.115000] pid_max: default: 4096 minimum: 301

[ 0.120000] Mount-cache hash table entries: 1024

[ 0.125000] Starting run_ksoftirqd, stack (thread_info) at 865ec000 cpu 0

[ 0.130000] NET: Registered protocol family 16

[ 0.135000] Topaz heap 1 in SRAM 98015e20<->98020000

[ 0.140000] Topaz heap 2 in SRAM 98011000<->98012000

[ 0.150000] bio: create slab <bio-0> at 0

[ 0.155000] pci 0000:00:00.0: reg 10: [io 0x0000-0x00ff]

[ 0.160000] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x00003fff 64bit]

[ 0.165000] pci 0000:00:00.0: supports D1 D2

[ 0.170000] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold

[ 0.175000] pci 0000:00:00.0: PME# disabled

[ 0.180000] pcibios_fixup_bus called bus name no 0 flags 0 next_dev 8f817400

[ 0.185000] pcibios_fixup_bus: Device [ 0: 0.0] has mem 1 io 1 cmd 0

[ 0.190000] pcibios_fixup_bus: Enabling I/O for device [ 0: 0.0]

[ 0.195000] pcibios_fixup_bus: Enabling memory for device [ 0: 0.0]

[ 0.200000] pci 0000:00:00.0: BAR 2: assigned [mem 0xc0000000-0xc0003fff 64bit]

[ 0.205000] pci 0000:00:00.0: BAR 2: set to [mem 0xc0000000-0xc0003fff 64bit] (PCI address [0xc0000000-0xc0003fff]

[ 0.210000] pci 0000:00:00.0: BAR 0: can't assign io (size 0x100)

[ 0.215000] pci_bus 0000:00: resource 1 [mem 0xc0000000-0xc1ffffff]

[ 0.220000] PCI Bus Scan completed!

[ 0.225000] watch64: 2003/08/22 Josef 'Jeff' Sipek <jeffpc@xxxxxxxxxxxxx>

[ 0.230000] watch64: Enabling Watch64 extensions...done.

[ 0.235000] Switching to clocksource ARC Timer1

[ 0.245000] NET: Registered protocol family 2

[ 0.250000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)

[ 0.255000] TCP established hash table entries: 8192 (order: 3, 65536 bytes)

[ 0.260000] TCP bind hash table entries: 8192 (order: 2, 32768 bytes)

[ 0.265000] TCP: Hash tables configured (established 8192 bind 8192)

[ 0.270000] TCP reno registered

[ 0.270000] NET: Registered protocol family 1

[ 0.275000] PCI: CLS 0 bytes, default 32

[ 1.120000] JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc.

[ 1.125000] msgmni has been set to 304

[ 1.130000] io scheduler noop registered (default)

[ 1.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled

[ 1.570000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A

[ 1.575000] console [ttyS0] enabled, bootconsole disabled

[ 1.585000] brd: module loaded

[ 1.590000] loop: module loaded

[ 1.600000] spi_flash: Force not to support Protect Mode

[ 1.605000] 6 cmdlinepart partitions found on MTD device spi_flash

[ 1.610000] Creating 6 MTD partitions on "spi_flash":

[ 1.615000] 0x000000000000-0x000000020000 : "uboot"

[ 1.620000] mtd: partition uboot is readonly

[ 1.630000] 0x000000020000-0x000000030000 : "uboot_env"

[ 1.635000] mtd: partition uboot_env is readonly

[ 1.640000] 0x000000030000-0x000000040000 : "uboot_env_bak"

[ 1.650000] 0x000000040000-0x000000a20000 : "linux_safety"

[ 1.660000] 0x000000a20000-0x000001400000 : "linux_live"

[ 1.665000] 0x000001400000-0x000002000000 : "data"

[ 1.675000] spi_flash: SPI flash driver initialized successfully!

[ 1.680000] ruby_health loading

[ 1.685000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000

[ 2.085000] HBM meta: emac rx 0x63c040 to 0x6bc040, wmac rx 0x6bc080 to 0x6dc080

[ 2.090000] topaz_hbm_init_pool_list pool 0 pool_list 0x98000000 bus_range 0x816ec400 to 0x826ec400 sz 2048 count 8192

[ 2.090000] topaz_hbm_init_pool_list pool 1 pool_list 0x98008000 bus_range 0x826fc400 to 0x848fc400 sz 17408 count 2048

[ 2.090000] topaz_hbm_init_pool_list pool 3 pool_list 0x9800a000 bus_range 0x0 to 0x0 sz 0 count 4096

[ 2.095000] topaz_busmon_init success

[ 2.100000] topaz_temp_sens_init success

[ 2.105000] u32 classifier

[ 2.105000] input device check on

[ 2.110000] Actions configured

[ 2.115000] Netfilter messages via NETLINK v0.30.

[ 2.120000] nf_conntrack version 0.5.0 (2434 buckets, 9736 max)

[ 2.130000] TCP cubic registered

[ 2.135000] NET: Registered protocol family 10

[ 2.140000] NET: Registered protocol family 17

[ 2.145000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

[ 2.150000] All bugs added by David S. Miller <davem@redhat.com>

D[ 2.165000] Freeing unused kernel memory: 26488k freed [8493a000] TO [86318000]

[ 2.170000] Common mmap addr-space starts 290f0000

init started: BusyBox v1.10.3 (2020-01-14 10:42:01 CST)

starting pid 62, tty '': '/etc/init.d/rcS'

[ 2.720000] load_module: 'bootcfg' using DRAM (offset:0x8d3d0000, size:0x9acd)

/scripts/cmdloop starting /scripts/ubus_evt_handler_d, at 00:00:03 up 0 min, load average: 0.00, 0.00, 0.00

/scripts/cmdloop starting /usr/sbin/ubusd, at 00:00:03 up 0 min, load average: 0.00, 0.00, 0.00

/etc/init.d/S02notifier: line 14: /usr/sbin/notifier: not found

Initializing random number generator... done.

/mnt/jffs2/wireless_conf.txt not found. Creating a default conf file

restore_wireless_conf

restore_wireless_conf: wifi_mode = default

restore_wireless_conf: Setting default wireless config params

restore_wireless_conf: board_id = 65535

restore_wireless_conf: board_name = QHS860

restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt

Starting network...

[ 4.725000] load_module: 'rtl8367b' using DRAM (offset:0x8d400000, size:0x32a1d)

[ 4.735000] rtl8367b: module license 'unspecified' taints kernel.

[ 4.740000] Disabling lock debugging due to kernel taint

[ 4.795000] load_module: 'emaclib' using DRAM (offset:0x8d3c8000, size:0x549b)

[ 4.925000] load_module: 'switch_vlan' using DRAM (offset:0x8d320000, size:0x28b6), SRAM (offset:0x98015e28, size:0x1)

[ 5.050000] load_module: 'switch_tqe' using DRAM (offset:0x8d328000, size:0x5728), SRAM (offset:0x98015e38, size:0x4)

[ 5.105000] tqe_descs_alloc: 512 tqe_rx_descriptors at kern uncached 0x4f0b9e60 bus 0x98015e60

[ 5.195000] load_module: 'fwt_if' using DRAM (offset:0x8d2ca000, size:0x1aad)

[ 5.230000] load_module: 'fwt_ctrl' using DRAM (offset:0x8d440000, size:0x23aea)

[ 5.265000] Failed to allocate SRAM IP-MAC lookup table, size 0x608

[ 5.285000] load_module: 'dpi' using DRAM (offset:0x8d376000, size:0x1d5d)

[ 5.320000] load_module: 'switch_emac' using DRAM (offset:0x8d2e4000, size:0x25e9), SRAM (offset:0x98018298, size:0x2f8)

[ 5.390000] emac wbsp: 0

[ 5.395000] enable A2 (single)

[ 5.455000] Random stuff 44

[ 6.115000] emac_eth_mii: probed

[ 6.115000] emac_lib eth1_emac0: index 0 id 0x1cc915 addr 0

[ 6.120000] emac_lib eth1_emac0: index 1 id 0x1cc915 addr 1

[ 6.125000] emac_lib eth1_emac0: index 3 id 0x1cc915 addr 3

[ 6.130000] emac_lib eth1_emac0: phy_id 0x1cc915 addr 1

[ 6.165000] emac_lib eth1_emac0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=mdio_bus, irq=-1)

[ 6.820000] emac_eth_mii: probed

[ 6.820000] emac_lib eth1_emac1: index 0 id 0x1cc915 addr 0

[ 6.825000] emac_lib eth1_emac1: index 1 id 0x1cc915 addr 1

[ 6.830000] emac_lib eth1_emac1: index 3 id 0x1cc915 addr 3

[ 6.835000] emac_lib eth1_emac1: phy_id 0x1cc915 addr 3

[ 6.870000] emac_lib eth1_emac1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=mdio_bus, irq=-1)

emac0 is eth1_1, emac1 is eth1_0

Stateless mode. Using temporary ip address:

Using IP address 192.168.1.50

Using netmask 255.255.255.0

cat: can't open '/mnt/jffs2/eth_macaddr': No such file or directory

[ 7.540000] device eth1_0 entered promiscuous mode

[ 7.545000] br0: port 1(eth1_0) entering forwarding state

[ 7.550000] br0: port 1(eth1_0) entering forwarding state

[ 7.720000] device eth1_1 entered promiscuous mode

/sbin/ifup -a

[ 7.910000] ADDRCONF(NETDEV_UP): eth1_1: link is not ready

Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.146

Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.226

Selected database version: Regulatory db version: v37.4.0.226

Using /etc/qtn_regulatory_db.bin

[ 8.120000] wizelink7531.tti.tv will be hijacked

dnsmasq: started, version 2.22 cachesize 150

dnsmasq: cleared cache

/scripts/cmdloop starting /usr/sbin/ndev, at 00:00:08 up 0 min, load average: 0.16, 0.03, 0.01

Starting qevt_server

Telnet disabled

/scripts/cmdloop starting /sbin/qevt_server, at 00:00:08 up 0 min, load average: 0.16, 0.03, 0.01

PCIe host enabled

[ 8.835000] load_module: 'qdpc_host' using DRAM (offset:0x8d580000, size:0x5898), SRAM (offset:0x9801e638, size:0xf84)

[ 8.950000] br0: port 1(eth1_0) entering forwarding state

Jan 1 00:00:09 qevt_server: Dot11Msg:Interface status change TRUE

ifconfig: host0: error fetching interface information: Device not found

[ 9.245000] eth1_1: link up (1000/Full)

[ 9.245000] ADDRCONF(NETDEV_CHANGE): eth1_1: link becomes ready

[ 9.250000] br0: port 2(eth1_1) entering forwarding state

[ 9.255000] br0: port 2(eth1_1) entering forwarding state

Jan 1 00:00:09 qevt_server: Dot11Msg:Interface status change TRUE

[ 9.395000] FWT: [ac:6f:bb:b0:dd:2a] add entry, port:emac0 node:0 index:987 4addr:0 entries:1

[ 9.565000] load_module: 'hw_rev' using DRAM (offset:0x8d37c000, size:0x360e)

Starting wireless...

restore_default_config -nr

restore_wireless_conf ap

restore_wireless_conf: wifi_mode = ap

restore_wireless_conf: Setting default wireless config params

restore_wireless_conf: board_id = 65535

restore_wireless_conf: board_name = QHS860

restore_wireless_conf: Writing config params to /mnt/jffs2/wireless_conf.txt

restore_default_config: Updating security config files for mode ap

restore_default_config: Removing block ACK restrictions

restore_default_config: Configuration has been set to default values. Reboot after customizing to ensure correct operation.

[ 11.205000] FWT: [ac:6f:bb:19:45:aa] add entry, port:emac0 node:0 index:349 4addr:0 entries:2

complete

[ 13.930000] FWT: [6a:de:cd:da:ab:a2] add entry, port:emac0 node:0 index:1016 4addr:0 entries:3

Using IP address 192.168.1.50

Using netmask 255.255.255.0

Loading modules

[ 16.305000] load_module: 'qtn_debug' using DRAM (offset:0x8d3fb400, size:0x32d)

[ 16.385000] load_module: 'i2cbus' using DRAM (offset:0x8d3a2000, size:0x1c84)

[ 16.500000] load_module: 'qtsens' using DRAM (offset:0x8d2ec800, size:0x76c)

[ 16.590000] load_module: 'pm_interval' using DRAM (offset:0x8d2f8000, size:0x14f8)

[ 16.750000] load_module: 'wlan' using DRAM (offset:0x8d700000, size:0xc3823)

[ 17.110000] FWT: [34:f3:9a:25:e3:38] add entry, port:emac0 node:0 index:397 4addr:0 entries:4

[ 17.130000] wlan: 0.8.4.2 (0.9.3.3)

[ 17.330000] load_module: 'auc_fw' using DRAM (offset:0x8d266000, size:0x884)

[ 17.450000] load_module: 'qvspmod' using DRAM (offset:0x8d504000, size:0x3eab)

[ 17.485000] QVSP module init

[ 17.550000] load_module: 'qdrv' using DRAM (offset:0x85800000, size:0xa783a)

[ 17.885000] qdrv wbsp: 0

[ 17.990000] load_module: 'wlan_xauth' using DRAM (offset:0x8d55bc00, size:0x2e4)

[ 18.050000] br0: no IPv6 routers present

[ 18.100000] load_module: 'wlan_ccmp' using DRAM (offset:0x8d3ee000, size:0x1734)

[ 18.220000] load_module: 'wlan_tkip' using DRAM (offset:0x8d680000, size:0x25e8)

Loading MuC driver (qtn_driver.qtn_ruby_spartan.0.bin)

no keyfile specified

unable to load Public Key

Waiting for Wireless Events from interfaces...

[ 19.730000] set power_selection 2

[ 19.740000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0

[ 19.745000] ..... Current RFIC Chip ID -- 4

[ 19.910000] AuC SRAM start 0x98040000 end 0x98070000 size 196608

[ 19.915000] AuC is configured for MU-enabled SRAM layout

[ 19.920000] AuC SRAM bank 0 start 0x98040000 end 0x98050000

[ 19.925000] AuC SRAM bank 1 start 0x98050000 end 0x98060000

[ 19.930000] AuC SRAM bank 2 start 0x98060000 end 0x98070000

[ 19.990000] qdrv_mac_reserve_clear: mac reservation table cleared

[ 20.005000] qdrv_wlan_80211_updateslot: vap is NULL

[ 20.010000] QDRV: I2C dapter not found

[ 20.140000] qdrv_mu_stat_init

[ 20.200000] MuC: g_tqe_sem_en 0

[ 20.200000] MuC: build date Mon, 25 Nov 2019 15:28:45 +0800

[ 20.205000] MuC: slow heap begin=0x802a5a00 end=0x80422a00

[ 20.210000] MuC: fast heap begin=0x98030800 end=0x98037000

[ 20.215000] MuC: stack start=0x9803ef80 sp=0x9803f6d4

[ 20.220000] MuC: calstate is 3 (prod), dcache on

[ 20.225000] MuC: RFIC version 1 rev 0

[ 20.225000] MuC: bb_init: FEM 0x7 bw_mode 0 chan 0 11b 0 11a 1

[ 20.230000] MuC: set max/nrm gain(0x27) done.

[ 20.235000] MuC: set cca threshold!

[ 20.240000] MuC: rf_optimizing_rf_register_map, set rf to 0x75

[ 20.245000] MuC: os_uc, after bb_rf_complete_attach.

[ 20.250000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740

[ 20.255000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0

[ 20.260000] MuC: freq 1 proj 1

[ 20.265000] MuC: dynamic one-bit autocorrelation enabled

[ 20.270000] MuC: QMAT SRAM base 0x98070000

[ 20.275000] MuC: enable IRQs

[ 20.290000] MuC: AuC enabled 0xe5101d24/0x60053840 il 0xe51012dc/0xe51012e0 stats 0x60051180/0x600535800x6006d93c

[ 20.295000] MuC: Update MU debug flag from 0x00000000 to 0x20000000

[ 20.300000] AuC: Update mu flag : 0x20000000. Max delay = 0, atf MU-vopt flag 0

[ 20.305000] QDRV: hardware is 4x4 11ac FO RGMII DBDC QV860

[ 20.310000] MuC boot succeeded 0.170 seconds

start-vap repeater

[ 21.740000] load_module: 'wlan_scan_ap' using DRAM (offset:0x8d5f0000, size:0x3ce8)

[ 21.885000] load_module: 'wlan_scan_sta' using DRAM (offset:0x8d6f4000, size:0x3804)

[ 21.965000] QTM daemon registered

[ 22.110000] qdrv_wlan_80211_updateslot: vap is NULL

[ 22.115000] qvsp_nl_node_init: QVSP not initialized

Jan 1 00:00:22 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:[ 22.150000] VAP create succeeded 0.030 seconds

00:22 qevt_server: Dot11Msg:Interface status change FALSE

[ 23.210000] MuC: calibration ver 0x801

Jan 1 00:00:23 iwevent: 00:00:23.407326 wifi0 Custom driver event:Dot11Msg: Channel Changed to 40 (reason 4)

bss_tm set to 1

neigh_repo reset to 0

Interface doesn't accept private ioctl...

neigh_repo (8BE0): Operation not supported

radar in 80MHZ mode

Setting mode to 11ac80

Jan 1 00:00:25 local_init_tx_power_table[1562]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

set_region: Setting regulatory region dev_name=wifi0 region=us mode=sta repeater=1

Jan 1 00:00:25 local_init_tx_power_table[1599]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

[ 25.600000] channel 116 is added into non-primary channel list

Jan 1 00:00:25 [ 25.610000] channel 120 is added into non-primary channel list

local_regulatory_set_chan_list[1[ 25.615000] channel 124 is added into non-primary channel list

599]: Set channel 116 as inactiv[ 25.620000] channel 128 is added into non-primary channel list

e primary channe[ 25.625000] Warning: all the sub channels are not in primary channel list!

Jan 1 00:00:25 local_regulatory_set_chan_[ 25.635000] channel 140 is added into non-primary channel list

list[1599]: Set channel 120 as i[ 25.640000] channel 144 is added into non-primary channel list

nactive primary channel

Jan 1 00:00:25 local_regulatory_set_chan_list[1599]: Set channel 124 as inactive primary channel

Jan 1 00:00:25 local_regulatory_set_chan_list[1599]: Set channel 128 as inactive primary chan[ 25.660000] DFS_s_radio: parameters updated, region: us

nel

Jan 1 0[ 25.665000] MuC: macfw: radar_start.........

0:00:25 local_re[ 25.670000] MuC: radar_start, region us = 1

gulatory_set_chan_list[1599]: Set channel 140 as inactive primary channel

Jan 1 00:00:25 local_regulatory_set_chan_list[1599]: Set channel 144 as inactive primary channel

radar start with regulatory us

dfs_s_radio 0 dfs 0 non-dfs 0 scan 0 auto-channel channel 36

Jan 1 00:00:27 Set Channel[1655]: freq 36, wrq.u.freq.e 0, wrq.u.freq.m 36

Jan 1 00:00:27 iwevent: 00:00:27.360073 wifi0 Set Frequency=5.18 GHz (Channel 36)

[ 27.370000] device wifi0 entered promiscuous mode

Jan 1 00:00:27 qevt_server: Dot11Msg:Interface status change FALSE

[ 27.590000] Enabling SSDP flooding

[ 27.880000] MuC: #RX data path optimal flag 0

[ 27.885000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x9800f000/6592 cache 0x9802aba0/13184

[ 27.890000] MuC: auto cs is enabled

[ 27.925000] WPS: push button GPIO pin 6

[ 27.925000] WPS: monitored using polling

[ 27.930000] WPS: active logic is low

[ 27.940000] br0: port 3(wifi0) entering forwarding state

[ 27.945000] br0: port 3(wifi0) entering forwarding state

Jan 1 00:00:28 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:00:29 iwevent: 00:00:29.527197 wifi0 Set Mode:Managed

Jan 1 00:00:29 iwevent: 00:00:29.536087 wifi0 Set ESSID:"g.isQ.J.)......F|.T.....vZ.c3..."

Jan 1 00:00:29 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:00:29 iwevent: 00:00:29.658687 wifi0 Set ESSID:"7531_5G---"

Beamforming enabled

Jan 1 00:00:30 iwevent: 00:00:30.616493 wifi0 Custom driver event:SCS: stats task is started

Jan 1 00:00:30 iwevent: 00:00:30.716516 wifi0 Set ESSID:"7531_5G---"

[ 30.725000] Enabling SCS

Jan 1 00:00:30 iwevent: 00:00:30.956513 wifi0 Custom driver event:SCS: channel sampling started - interval is 5 seconds

SCS enabled

[ 30.955000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done

Jan 1 00:00:31 [ 30.980000] VAP create succeeded 0.020 seconds

qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:00:31 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:00:31 Set Channel[1864]: freq 36, wrq.u.freq.e 0, wrq.u.freq.m 36

Jan 1 00:00:31 iwevent: 00:00:31.291690 wifi0 Custom driver event:Dot11Msg: Channel Changed to 36 (reason 3)

Jan 1 00:00:31 iwevent: 00:00:31.292670 wifi0 Set Frequency=5.18 GHz (Channel 36)

Jan 1 00:00:31 local_init_tx_power_table[1865]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 116 as inactive primary channel

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 120 as inactive primary channel

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 124 as inactive primary channel

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 128 as inactive primary channel

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 140 as inactive primary channel

Jan 1 00:00:31 local_regulatory_set_chan_list[1865]: Set channel 144 as inactive primary channel

radar start with regulatory us

Jan 1 00:00:31 802.11d Set country code[1865]: country code set to us

Jan 1 00:00:31 iwevent: 00:00:31.906668 wifi0 Set ESSID:"7531_5G---"

Jan 1 00:00:31 iwevent: 00:00:31.907646 wifi0 Custom driver event:SCAN ABORT

Configuration file: /mnt/jffs2/hostapd.conf

Line 2: DEPRECATED: 'dump_file' configuration variable is not used anymore

[ 33.070000] device wifi1 entered promiscuous mode

Jan 1 00:00:33 qevt_server: Dot11Msg:Interface status change FALSE

madwifi_sta_deauth: Interface not up.

Jan 1 00:00:33 qevt_server: Dot11Msg:Interface status change FALSE

Using interface wifi1 with hwaddr A6:6F:BB:AC:35:88 and ssid "7531_5G---"

Jan 1 00:00:33 iwevent: 00:00:33.611983 wifi1 Set ESSID:"7531_5G---"

Jan 1 00:00:33 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:00:33 qevt_serve[ 33.485000] VAP create succeeded 0.020 seconds

r: Dot11Msg:Interface status change FALSE

[ 33.515000] device wifi2 entered promiscuous mode

Jan 1 00:00:33 qevt_server: Dot11Msg:Interface status change FALSE

madwifi_sta_deauth: Interface not up.

Using interface wifi2 with hwaddr AA:6F:BB:AC:35:88 and ssid "Wizelink_Guest"

Jan 1 00:00:34 iwevent: 00:00:34.099946 wifi2 Set ESSID:"Wizelink_Guest"

Jan 1 00:00:34 qevt_server: Dot[ 34.045000] br0: port 4(wifi1) entering forwarding state

11Msg:Interface [ 34.050000] br0: port 4(wifi1) entering forwarding state

status change TRUE

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change TRUE

[ 34.065000] br0: port 4(wifi1) entering forwarding state

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change TRUE

[ 34.185000] br0: port 5(wifi2) entering forwarding state

[ 34.190000] br0: port 5(wifi2) entering forwarding state

[ 34.205000] br0: port 5(wifi2) entering forwarding state

wifi1: interface state UNINITIALIZED->ENABLED

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change FALSE

wifi1: AP-ENABLED

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change FALSE

[ 34.390000] BRIDGE WLAN report flood-forwarding enablednge FALSE

Jan 1 00:00:34 qevt_server: Dot11Msg:Interface status change FALSE

[ 35.180000] FWT: [18:bb:26:6d:fe:9b] add entry, port:emac0 node:0 index:950 4addr:0 entries:5

complete

sh: -le: argument expected

Repeater max level is invalid, set to default 2

complete

Jan 1 00:00:35 qevt_server: Dot[ 35.580000] br0: port 4(wifi1) entering forwarding state

11Msg:Interface [ 35.585000] br0: port 4(wifi1) entering forwarding state

status change TRUE

Jan 1 00:00:35 qevt_server: Dot11Msg:Interface status change TRUE

complete

Starting qrpe daemon...

qtna-rpe(9.0.0-f34af82) started

/scripts/cmdloop starting /usr/sbin/csmd, at 00:00:36 up 0 min, load average: 0.72, 0.18, 0.06

[csmd]: (1.3.10-enhance-v1-348cdb6-1962215-c903c7e) started(0x2a178)

0000000036 [Info..] [QSPD] (spdia_init :0438) loaded Q-SPDIA lib

SONiQ-sl.qtn(3.3.10-enhance-v1-1962215) loaded

0000000036 [Info..] [CSM ] (csm_create_radio_db :0908) Create Radio database with max size = 0

0000000036 [Info..] [CSM ] (csm_create_bss_db :0874) Create BSS database with max size = 0

0000000036 [Info..] [CSM ] (csm_create_station_d:0800) Create station database with max size = 1024

Pause connecting, will resume after backhaul_manager determine the mode

Selected interface 'wifi0'

/scripts/cmdloop starting /usr/sbin/backhaul_diagnose, at 00:00:36 up 0 min, load average: 0.72, 0.18, 0.06

/scripts/cmdloop starting /usr/sbin/backhaul_manager, at 00:00:36 up 0 min, load average: 0.72, 0.18, 0.06

[ 36.495000] FWT: [d8:fe:e3:a4:d9:b4] add entry, port:emac0 node:0 index:918 4addr:0 entries:6

[backhaul_manager NOTICE L:1157 T:36] set backhaul from unknown to ethernet

No core dump generated

dnsmasq: started, version 2.22 cachesize 150

dnsmasq: cleared cache

monitor reset button

Stopping DHCP client

[ 38.170000] wifi0: no IPv6 routers present

DHCP client enabled

[backhaul_manager NOTICE L:1113 T:38] set mode from undetermined to booster

[ 38.680000] Build name: v37.4.0.226

[ 38.685000] Build revision: 99177

[ 38.690000] Build type: SDK

[ 38.690000] Build timestamp: 1564675932

[ 38.695000] Platform ID: 465

[ 38.700000] Hardware ID: QV860

[ 38.705000] Hardware revision: bbic4_rev_a2

[ 38.710000] Band: 5GHz

[ 38.715000] Kernel version: 2.6.35

[ 38.715000] Calibration version: disabled

[ 38.720000] DC/IQ cal version: V8.1

[ 38.725000] Power cal version: V8.1

[ 38.730000] MuC firmware: qtn_driver.qtn_ruby_spartan.0.bin

[ 38.735000] DSP firmware: rdsp_driver.0.bin

[ 38.740000] AuC firmware: auc_driver.default.0.bin

[ 38.745000] MAC address 0: ac:6f:bb:ac:35:88

[ 38.750000] MAC address 1: 00:00:00:00:00:00

[ 38.755000] Recommended U-Boot: SEv1.2v37.4.0.198

Carrier ID 0, uboot update flag 0

complete

[ 39.765000] QDRV: src ip addr 192.168.0.104

[ 39.920000] MuC: Update MU debug flag from 0x20000000 to 0x20000000

[ 39.920000] MuC: MU disabled

[ 39.920000] AuC: Update mu flag : 0x20000000. Max delay = 0, atf MU-vopt flag 0

[ 39.965000] MuC: Update MU debug flag from 0x20000000 to 0x20000000

[ 39.965000] AuC: Update mu flag : 0x20000000. Max delay = 0, atf MU-vopt flag 0

PTA request polarity set to 0

PTA grant polarity set to 0

[ 40.820000] Netdebug is disabled

PTA disabled

[ 40.930000] Ratedebug is disabled

Jan 1 00:00:42 iwevent: 00:00:42.841538 wifi0 Scan request completed

[ 46.430000] wifi1: no IPv6 routers present

[ 46.680000] Disabling SCS

Jan 1 00:00:46 iwevent: 00:00:46.919305 wifi0 Custom driver event:SCS: channel sampling disabled

Jan 1 00:00:46 iwevent: 00:00:46.967332 wifi0 Custom driver event:SCS: stats task is stopped

Jan 1 00:00:47 Contact Security Daemon[2445]: SET tdls_disabled 1: got reply OK

[ 47.145000] device wifi2 left promiscuous mode

[ 47.145000] br0: Jan 1 00:00:47 qevt_server: Dot11Msg:Interface pstatus change FAoLSE

Jan 1 00:00:47 qevt_server: Dot11Msg:Interface status change FALSE

rt 5(wifi2) entering disabled state

[ 47.165000] qdrv_tx_done_flush_vap: 0 bufs retrieved in 0 msecs

[ 47.430000] VAP delete succeeded 0.250 seconds

[ 47.560000] br0: port 4(wifi1) entering forwarding state

Jan 1 00:00:47 qevt_server: Dot11Msg:Interface status change FALSE

[ 49.730000] qdrv_tx_done_flush_vap: 0 bufs retrieved in 0 msecs

[ 49.730000] device wifi1 left promiscuous mode

[ 49.730000] br0: port 4(wifi1) entering disabled state

[ 49.990000] VAP delete succeeded 0.250 seconds

Jan 1 00:00:50 qevt_server: Dot11Msg:Interface status change TRUE

[ 50.525000] br0: portJan 1 00:00:50 iwevent: [trunca ted] ]..X.^.....3..T...tA!=.."

(

wifi0) entering forwarding state

Jan 1 00:00:50 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:00:50 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:00:51 qevt_server: Dot11Msg:Interface status change FALSE

[ 55.280000] qdrv_tx_done_flush_vap: 0 bufs retrieved in 0 msecs

[ 55.285000] device wifi0 left promiscuous mode

[ 55.285000] br0: port 3(wifi0) entering disabled state

[ 55.305000] VAP delete succeeded 0.010 seconds

[ 58.380000] load_module: 'wlan_scan_ap' using DRAM (offset:0x8d5f0000, size:0x3ce8)

[ 58.605000] qdrv_wlan_80211_updateslot: vap is NULL

[ 58.605000] qvsp_nl_Jan 1 00:00:58 qevt_server: Dotn11Msg:Interface ostatus change FAdLSE

Jan 1 00:e00:58 qevt_server: Dot11Msg:Interface status change FALSE

_init: QVSP not initialized

[ 58.605000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done

[ 58.625000] VAP create succeeded 0.010 seconds

Jan 1 00:00:59 local_init_tx_power_table[2756]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 116 as inactive primary channel

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 120 as inactive primary channel

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 124 as inactive primary channel

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 128 as inactive primary channel

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 140 as inactive primary channel

Jan 1 00:00:59 local_regulatory_set_chan_list[2756]: Set channel 144 as inactive primary channel

Jan 1 00:00:59 802.11d Set country code[2756]: country code set to us

Jan 1 00:01:01 local_init_tx_power_table[2862]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

Jan 1 00:01:01 local_init_tx_power_table[2886]: loading power table from /etc/power_tables/tx_power_QSR1000_us.txt

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 116 as inactive primary channel

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 120 as inactive primary channel

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 124 as inactive primary channel

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 128 as inactive primary channel

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 140 as inactive primary channel

Jan 1 00:01:01 local_regulatory_set_chan_list[2886]: Set channel 144 as inactive primary channel

Jan 1 00:01:01 802.11d Set country code[2886]: country code set to us

Jan 1 00:01:02 Set Channel[2916]: freq 0, wrq.u.freq.e 0, wrq.u.freq.m 0

Jan 1 00:01:02 iwevent: 00:01:02.718102 wifi0 Set Channel=0

[ 62.665000] device wifi0 entered Jan 1 00:01:02 qevt_server: Dot11Msg:Interface pstatus change FArLSE

Jan 1 00:o01:02 qevt_servemr: Dot11Msg:Interface status change FALSE

uan 1 00:01:02 qevti_server: Dot11Mssg:Interface statcus change FALSE

ous mode

[ 62.800000] Enabling SSDP flooding

Jan 1 00:01:03 iwevent: 00:01:03.641629 wifi0 Custom driver event:SCS: stats task is started

[ 63.545000] Enabling SCS

Jan 1 00:01:03 iwevent: 00:01:03.783642 wifi0 Custom driver event:SCS: channel sampling started - interval is 5 seconds

[ 64.620000] BRIDGE WLAN report flood-forwarding enabled

Jan 1 00:01:06 iwevent: 00:01:06.303504 wifi0 Set ESSID:"7531_5G---"

Jan 1 00:01:06 qevt_server: Dot11Msg:Interface status change FALSE

[ 66.165000] VAP create succeeded 0.020 secoJan 1 00:01:06 nqevt_server: Dotd11Msg:Interface sstatus change FA

LSE

[ 66.195000] device Jan 1 00:01:06 qevt_server: Dot11Msg:Interface wstatus change FAiLSE

Jan 1 00:f01:06 qevt_serveir: Dot11Msg:Interface status change FALSE

nan 1 00:01:06 qevt1_server: Dot11Ms g:Interface stateus change FALSE

tered promiscuous mode

Jan 1 00:01:06 iwevent: 00:01:06.800351 wifi1 Set ESSID:"Wizelink_Guest"

[ 66.735000] WPS: push button GPIO pin 6

[ Jan 1 00:01:06 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:01:06 qevt_server: Dot11Msg:Inter face status chan6ge TRUE

6.735000] WPS: monitored using polling

[ 66.735000] WPS: active logic is low

[ 66.740000] br0: port 3(wifi0) entering forwarding state

[ 66.755000] br0: port 3(wifi0) entering forwarding state

Jan 1 00:01:07 qevt_server: Dot11Msg:Interface status change TRUE

[ 66.900000] br0: port 4(wifi1) entering forwarding state

Jan 1 00:01:07 qevt_server: Dot11Msg:Interface status change FA[LSE

Jan 1 00: 01:07 qevt_serve r: Dot11Msg:Inte rface status change FALSE

66.960000] br0: port 4(wifi1) entering forwarding state

Jan 1 00:01:07 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:01:07 qevt_server: Dot11Msg:Interface status change TRUE

Jan 1 00:01:07 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:01:07 dfs_daemon[2376]: scs_enabled = 1

Jan 1 00:01:07 dfs_daemon[2376]: debug = 3

'monitor_temperature' is not enabled/set

Jan 1 00:01:07 dfs_daemon[2376]: syslog = 1

Jan 1 00:01:07 dfs_daemon[2376]: console_print = 0

Jan 1 00:01:07 dfs_daemon[2376]: region = us

Jan 1 00:01:07 dfs_daemon[2376]: config_file = /etc/dfs_daemon.conf

Jan 1 00:01:07 dfs_daemon[2376]: interface = wifi0

Jan 1 00:01:07 dfs_daemon[2376]: interval = 900

Jan 1 00:01:07 dfs_daemon[2376]: second_interval = 60

Jan 1 00:01:07 dfs_daemon[2376]: delay = 900

Jan 1 00:01:07 dfs_daemon[2376]: start_hour = 3

Jan 1 00:01:07 dfs_daemon[2376]: end_hour = 4

Jan 1 00:01:07 dfs_daemon[2376]: scs_rxtx_threshold = 100

Jan 1 00:01:07 dfs_daemon[2376]: scs_tx_threshold = 50

Jan 1 00:01:07 dfs_daemon[2376]: target_count = 2

Jan 1 00:01:07 dfs_daemon[2376]: curr_count = 0

Jan 1 00:01:07 dfs_daemon[2376]: time_offset = 0

Jan 1 00:01:07 dfs_daemon[2376]: score_threshold = 0

Jan 1 00:01:07 dfs_daemon[2376]: DFS Daemon v1.0 started, interval set to 900 seconds

Jan 1 00:01:07 dfs_daemon[2376]: scs_enabled = 1

Jan 1 00:01:07 dfs_daemon[2376]: qcsapi[wifi_get_channel] failed, error code = -34

Jan 1 00:01:07 dfs_daemon[2376]: sleep for 900 seconds

Product name: WizeLink

[ Jan 1 00:01:08 qevt_server: Dot 11Msg:Interface 6status change TR8UE

Jan 1 00:0.1:08 qevt_server4: Dot11Msg:Interface status change TRUE

25Jan 1 00:01:08 qevt_server: Dot011Msg:Interface 0status change TRUE

Jan 1 00:01:08 qevt_server: Dot11Msg:Interface status change FALSE

Jan 1 00:01:08 qevt_server: Do0t11Msg:Interface] status change F ALSE

br0: port 4(wifi1) entering forwarding state

[ 68.425000] br0: port 4(wifi1) entering forwarding state

[ 68.440000] br0: port 4(wifi1) entering forwarding state

NTP client enabled

MAUI service started

Dec 31 16:01:10 iwevent: 0:01:10.249511 wifi0 00:01:10.249511 wifi0 Set ESSID:"7531_5G---"

Set ESSID:"7531_5G---"

/scripts/cmdloop starting /sbin/qharvestd, at 16:01:10 up 1 min, load average: 1.36, 0.41, 0.14

Dec 31 16:01:10 qharvestd[3420]: qharvestd[notice]: qharvestd v1.34 started

Dec 31 16:01:11 iwevent: 00:01:11.433119 wifi1 00:01:11.433119 wifi1 Set ESSID:"Wizelink_Guest"

Set ESSID:"Wizelink_Guest"

Starting httpd

Dec 31 16:01:12 qharvestd[3420]: qharvestd[notice]: Pktlogger support detected

Starting cwmpd

[ Dec 31 16:01:12 qevt_server: Dot11Msg:Interface status change TR UE

Dec 31 16:01:12 qevt_server: Dot11Msg:Interface status change TRUE

72.560000] br0: port 3(wifi0) entering forwarding state

[ 72.560000] br0: port 3(wifi0) entering forwarding state

[ 74.365000] load_module: 'qwe_rpe' using DRAM (offset:0x855b8000, size:0x5c66)

[ 74.395000] Start RPE for QWE radio

[ Dec 31 16:01:15 qevt_server: Dot11Msg:Interface status change FALSE

Dec 31 16:01:15 qevt_server: Dot11Msg:Interface status change FALSE

74.560000] load_module: 'rtl8192cd' using DRAM (offset:0x85a00000, size:0x11bc12)

[ 74.745000] Realtek WLAN driver - version 3.6 (2017-07-07-v17)

[ 74.745000] Adaptivity function - version 9.3.4

[ 74.750000] Enabling MEM

[ 74.750000] MACHAL_version_init

[ 74.760000] tqe_descs_alloc: 4096 tqe_rx_descriptors at kern uncached 0x532e0000 bus 0x8d6c0000

[ 74.775000] tqe_pcie_netdev_init: tqe_sem_en 0

[ 74.780000] wlan0: PCI cache line size set incorrectly (0 bytes) by BIOS/FW,

[ 74.780000] The device 818b has PCI Express capability

[ 74.780000] RC cap:256, dev cap:128

[ 74.780000] Setting MPS to 128

[ 74.780000] not two slots, enable_efuse=1

[ 74.780000] page_ptr=7e282000, size=507248, ring_dma_addr:8e282000, alloc_dma_buf:7e280000, ring_virt_addr:7e282000

[ 74.805000] not two slots, enable_efuse=1

[ 74.815000] not two slots, enable_efuse=1

[ 74.830000] not two slots, enable_efuse=1

[ 74.850000] not two slots, enable_efuse=1

[ 74.870000] not two slots, enable_efuse=1

tti_led_quality_start

[ 76.105000] unlock_uboot_env: unlock successfully

Dec 31 16:01:16 Contact Security Daemon[3910]: WPS_UPNP_ENABLE wifi0 0: got reply

scid is not started

starting crond...

/scripts/cmdloop starting /usr/sbin/crond, at 16:01:19 up 1 min, load average: 1.57, 0.47, 0.16

Dec 31 16:01:19 crond[4082]: crond (busybox 1.10.3) started, log level 8

starting pid 4085, tty '/dev/console': '/bin/sh -l'

BusyBox v1.10.3 (2020-01-14 10:42:01 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off

quantenna # [ 79.795000] RADAR: CAC started for channel 52 (5260 MHz)

perform wlanup directly

<<<<<<<< begain wlanup

[ 82.950000] wifi0: no IPv6 routers present

[ 88.960000] WlanSupportAbility = 0x1

[ 88.970000] PrepareRXBD88XX(165):size=507248, ring_dma_addr:8e282000, alloc_dma_buf:7e280000, ring_virt_addr:7e282000

[ 88.970000] QNum: 0x0, RXBDHead: 0x7e282000, tmp_dma_ring_addr:0x8e282000

[ 88.975000] head:7e282000, ring_dma_addr:8e282000, size:1000

[ 88.975000] ptxbd_head:7e283000, tmp_tx_dma_ring_addr:8e283000

[ 88.975000] ptx_desc_head:7e2b3400, tmp_tx_dma_ring_addr2:8e2b3400, size: 20, 30

[ 88.975000] ptxbd_bcn_head:7e2fba00, tmp_tx_dma_ring_addr3:8e2fba00,

[ 88.975000] ptxdesc_bcn_head:7e2fbc80, tmp_tx_dma_ring_addr4:8e2fbc80,

[ 88.975000] PrepareTXBD88XX(550), q_num:0, TXBD_RWPtr_Reg:0x3b0, TXBD_Reg:0x310, ptxbd:7e283000 8e283000, ptx_desc:7e2b3400 8e2b3400

[ 88.975000] PrepareTXBD88XX(550), q_num:1, TXBD_RWPtr_Reg:0x3ac, TXBD_Reg:0x330, ptxbd:7e28b000 8e28b000, ptx_desc:7e2bf400 8e2bf400

[ 88.975000] PrepareTXBD88XX(550), q_num:2, TXBD_RWPtr_Reg:0x3a8, TXBD_Reg:0x328, ptxbd:7e293000 8e293000, ptx_desc:7e2cb400 8e2cb400

[ 88.975000] PrepareTXBD88XX(550), q_num:3, TXBD_RWPtr_Reg:0x3a4, TXBD_Reg:0x320, ptxbd:7e29b000 8e29b000, ptx_desc:7e2d7400 8e2d7400

[ 88.975000] PrepareTXBD88XX(550), q_num:4, TXBD_RWPtr_Reg:0x3a0, TXBD_Reg:0x318, ptxbd:7e2a3000 8e2a3000, ptx_desc:7e2e3400 8e2e3400

[ 88.975000] PrepareTXBD88XX(550), q_num:5, TXBD_RWPtr_Reg:0x3b8, TXBD_Reg:0x340, ptxbd:7e2ab000 8e2ab000, ptx_desc:7e2ef400 8e2ef400

[ 88.975000] PrepareTXBD88XX(550), q_num:6, TXBD_RWPtr_Reg:0x3bc, TXBD_Reg:0x348, ptxbd:7e2ac000 8e2ac000, ptx_desc:7e2f0c00 8e2f0c00

[ 88.975000] PrepareTXBD88XX(550), q_num:7, TXBD_RWPtr_Reg:0x3c0, TXBD_Reg:0x350, ptxbd:7e2ad000 8e2ad000, ptx_desc:7e2f2400 8e2f2400

[ 88.975000] PrepareTXBD88XX(550), q_num:8, TXBD_RWPtr_Reg:0x3c4, TXBD_Reg:0x358, ptxbd:7e2ae000 8e2ae000, ptx_desc:7e2f3c00 8e2f3c00

[ 88.975000] PrepareTXBD88XX(550), q_num:9, TXBD_RWPtr_Reg:0x3c8, TXBD_Reg:0x360, ptxbd:7e2af000 8e2af000, ptx_desc:7e2f5400 8e2f5400

[ 88.975000] PrepareTXBD88XX(550), q_num:10, TXBD_RWPtr_Reg:0x3cc, TXBD_Reg:0x368, ptxbd:7e2b0000 8e2b0000, ptx_desc:7e2f6c00 8e2f6c00

[ 88.975000] PrepareTXBD88XX(550), q_num:11, TXBD_RWPtr_Reg:0x3d0, TXBD_Reg:0x370, ptxbd:7e2b1000 8e2b1000, ptx_desc:7e2f8400 8e2f8400

[ 88.975000] PrepareTXBD88XX(550), q_num:12, TXBD_RWPtr_Reg:0x3d4, TXBD_Reg:0x378, ptxbd:7e2b2000 8e2b2000, ptx_desc:7e2f9c00 8e2f9c00

[ 88.975000] PrepareTXBD88XX(550), q_num:13, TXBD_RWPtr_Reg:0x0, TXBD_Reg:0x0, ptxbd:7e2b3000 8e2b3000, ptx_desc:7e2fb400 8e2fb400

[ 88.975000] PrepareTXBD88XX(550), q_num:14, TXBD_RWPtr_Reg:0x0, TXBD_Reg:0x308, ptxbd:7e2fba00 8e2fba00, ptx_desc:7e2fbc80 8e2fbc80

[ 88.975000] ptxbd_bcn[0]: 0x7e2fba00, Dword0: 0x28, Dword1: 0x8e2fbc80

[ 88.975000] ptxbd_bcn[1]: 0x7e2fba80, Dword0: 0x28, Dword1: 0x8e2fbcb0

[ 88.975000] ptxbd_bcn[2]: 0x7e2fbb00, Dword0: 0x28, Dword1: 0x8e2fbce0

[ 88.975000] ptxbd_bcn[3]: 0x7e2fbb80, Dword0: 0x28, Dword1: 0x8e2fbd10

[ 88.975000] ptxbd_bcn[4]: 0x7e2fbc00, Dword0: 0x28, Dword1: 0x8e2fbd40

[ 89.285000] [QWERPE] [Info ] (qwerpe_register_:2096)qwerpe bss [ac:6f:bb:ac:35:89] for wlan0 is created

[ 89.285000] [ODM_software_init][12372] BoardType = 0x0 rfe_type=0

[ 89.285000] eric-8822 [ODM_software_init][12581]

[ 89.285000] clock 40MHz

[ 89.285000]

[ 89.285000] ************* Initialize MAC/PHY parameter *************

[ 89.290000] [MAC_REG_8192Emp]

[ 89.290000] rtl8192e version = 58

[ 89.290000] [PHY_REG_8192Emp]

[ 89.290000] RTL8192E_MAC_PHY_Parameter_v021_MP_20130718

[ 89.290000] [PHY_REG_PG_8192Emp]

[ 89.290000] RL6286_MAC_PHY_Parameter_v024_20130125

[ 89.290000] [AGC_TAB_8192Emp]

[ 89.290000] RTL8192E_MAC_PHY_Parameter_v016_MP_20130705

[ 89.295000] RadioA_8192Emp

[ 89.295000] RTL8192E_MAC_PHY_Parameter_v023_MP_20130910

[ 89.635000] [RadioB_8192Emp]

[ 89.635000] RTL8192E_MAC_PHY_Parameter_v023_MP_20130910

[ 89.965000] [PHY_ConfigTXPwrTrackingWithParaFile 4359]

[ 89.965000] [PHY_ConfigTXPwrTrackingWithParaFile 4429] read_bytes=2283

[ 89.965000] [TxPowerTrack_AP]

[ 92.315000] eth1_0 emac_lib_mdio_read: warn: system is overloaded : spend more ~500ms!

[ 92.315000] HLINK MSG: waiting for MuC dequeue over 370 jiffies, re-trigger interrupt to muc

[ 92.365000] device wlan0 entered promiscuous mode

[ 92.365000] br0: port 5(wlan0) entering forwarding state

[ 93.115000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.170000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.185000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.260000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.295000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.330000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.380000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.390000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 93.400000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

>>>>>>>> finish wlanup

[ 99.825000] emac_lib_poll_wait: 3 callbacks suppressed

[ 99.825000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 99.850000] eth1_0 emac_lib_txstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 99.890000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 100.000000] eth1_0 emac_lib_rxstatistics_counter: warn: system is overloaded : spend more ~10ms!

[ 100.475000] [QWERPE] [Warn ] (rtl_get_intf_fat:0292)FAT is not measured yet, return dummy value 800

[ 100.490000] FWT: [ac:9c:e4:5f:83:51] add entry, port:emac0 node:0 index:494 4addr:0 entries:7

[ 102.350000] wlan0: no IPv6 routers present

[ 110.440000] FWT: [01:00:5e:7f:03:16] add entry, port:emac0 node:0 index:275 4addr:0 entries:8

acl rules is not enbled in config file

[ 149.920000] RADAR: CAC completed for channel 52 (5260 MHz)

quantenna #

Skyworker的筆記

2020年6月12日星期五

WAP-7531 MESH的開機程序

沒有留言:

張貼留言

2020年6月12日 星期五

WAP-7531 MESH的開機程序

沒有留言:

張貼留言

2020年6月12日星期五